Trailer technical guides

Measure and match axles, stud patterns, bearings, springs, brakes and wiring before you order.

Measuring and set-up guides for trailer axles, wheels, bearings, springs, brakes and wiring. Use them to check your parts before you order. If something doesn't match, call the parts counter on 07 3275 2885.

How to measure axle length

Axle length depends on the width of your trailer and the offset of your wheels. Measure the width where the springs mount, and the backspace of the rim with the tyre fitted. The calculator turns those two numbers into an overall axle length and the closest standard size.

Axle and axle kit pages also have a "Find your axle length" panel under the options, so you can check the size while you shop.

How to identify your stud pattern

The stud pattern is the number of wheel studs and the diameter of the circle they sit on (the PCD). Count the studs, measure from the centre of one stud to the centre of the next, then compare with the table below.

How to measure wheel stud pattern (PCD) for 4, 5 and 6 stud hubsMeasure S, the distance from the centre of one stud to the centre of the next stud. 4 stud: PCD equals S times 1.414, or centre to centre of opposite studs. 5 stud: PCD equals S times 1.701, as there is no opposite stud. 6 stud: PCD equals S times 2, or centre to centre of opposite studs. 4 STUD PCD S PCD = S × 1.414 or centre to centre of opposite studs 5 STUD PCD S PCD = S × 1.701 no opposite stud, so measure S 6 STUD PCD S PCD = S × 2 or centre to centre of opposite studs S = centre of one stud to centre of the next stud
How to measure your stud patternMeasure S between the centres of two neighbouring studs, then use the formula above or the table below.
Pattern Stud size Studs PCD (in) PCD (mm) Adjacent studs (in) Adjacent studs (mm)
Gemini 7/16″ 4 — 100.00 2 13/16″ 70.70
Mini 7/16″ 4 4″ 101.60 2 13/16″ 71.84
Capri 7/16″ 4 4 1/4″ 107.95 3″ 76.33
Cortina / Telstar 7/16″ 4 4 1/4″ 107.95 3″ 76.33
Datsun 1600 7/16″ 4 4 1/2″ 114.30 3 3/16″ 80.82
Early Ford 1/2″ 4 4 1/2″ 114.30 3 3/16″ 80.82
Toyota Corona 7/16″ 4 4 1/2″ 114.30 3 3/16″ 80.82
Valiant (to 1971) 7/16″ 5 4″ 101.60 — 59.72
Holden HT / HG / HK 7/16″ 5 4 1/4″ 107.95 2 1/2″ 63.45
Ford 1/2″ 5 4 1/2″ 114.30 2 5/8″ 67.18
Valiant (1971–72) 7/16″ 5 4 1/2″ 114.30 2 5/8″ 67.18
Commodore 7/16″ 5 — 120.00 2.776″ 70.53
Holden HQ / HJ / HX 7/16″ 5 4 3/4″ 120.65 2 13/16″ 70.91
Ford F100 1/2″ 5 5 1/2″ 139.70 3 1/4″ 82.11
Ford / Jeep 1/2″ 5 5 1/2″ 139.70 3 1/4″ 82.11
Land Rover 5/8″ 5 6 1/2″ 165.10 3 13/16″ 96.98
LandCruiser 100 Series 9/16″ 5 — 150.00 — 88.17
LandCruiser 4WD 1/2″ 6 5 1/2″ 139.70 2 3/4″ 69.85
Nissan Patrol 1/2″ 6 5 1/2″ 139.70 2 3/4″ 69.85
Nissan Navara D40 1/2″ 6 — 114.30 — —

More help: How to identify the stud pattern on your trailer.

How to identify your bearings

Most trailer wheel bearings can be identified by the number stamped on the bearing cone. If you can't read it, measure the bearing instead.

  1. Find the numbersRemove the hub and read the numbers stamped on the inner and outer bearing cones, for example LM67048 or L68149.
  2. Record inner and outerTrailer hubs normally use a larger inner bearing and a smaller outer bearing. Note both numbers.
  3. Measure if neededIf the numbers are worn off, measure the outside diameter, inside diameter and width with a vernier caliper.

Common Australian trailer bearing combinations

Type Position Dimensions (mm) Cup Cone Seal
LM / Holden Inner (large) 59.1 × 31.75 × 15.875 LM67010 LM67048 28560 (59mm OD × 37.5mm ID)
Outer (small) 45.237 × 19.05 × 15.494 LM11910 LM11949
SL / Ford Inner (large) 59.131 × 34.988 × 15.875 L68110 L68149 28600 (59mm OD × 40mm ID)
Outer (small) 45.237 × 21.986 × 15.494 LM12710 LM12749
Dexter 2T (D60) Inner (large) 82.931 × 44.450 × 23.812 25520 25580 33940 (85.5mm OD × 48.5mm ID)
Outer (small) 62 × 31.75 × 18.161 15123 15245
Parallel / ESS Inner (large) 59.131 × 34.988 × 15.875 L68110 L68149 28600 (59mm OD × 40mm ID)
Outer (same as inner) 59.131 × 34.988 × 15.875 L68110 L68149

The full chart also covers Composite, Dexter, USA/Dexter, TB500, AL-KO and Melbourne Turn combinations. It is for identification only. We may not stock every combination shown, so contact us if you're unsure.

Trailer spring set-up guides

Hanger and axle centre measurements for common suspension set-ups. These are a guide only. Check them against your own springs and hangers before you drill or weld.

Tandem rocker roller suspension measurements
Tandem rocker rollerHanger centres 787mm. Axle centres: 992mm (13–16″ wheels, outer centre), 785mm (13–14″ wheels, inner centre) or 888mm (15–16″ wheels, centred).
Tri-axle rocker roller suspension measurements
Tri-axle rocker rollerHanger and axle centre measurements.
Tri-axle rocker roller set-up for 15 to 16 inch rims
Tri-axle rocker roller, 15–16″ rims (centred)Hanger centres 790 / 890 / 790mm, axle centres 900mm.
Tandem rocker spring set-up measurements
Rocker spring (tandem)Axle centres 960mm with centred spring bolts, or 1046mm with off-centre spring bolts.
Off-road rebound suspension diagram
Off-road rebound suspensionMounting layout for eye to eye rebound kits.
Eye to eye shackle spring diagram
Eye to eye (shackle) springsHanger and shackle layout.
Eye to slipper spring diagram
Eye to slipper springs (6mm and 8mm)Front hanger and slipper layout.

Shop springs & suspension

Brake mounting plate location

Where to position brake mounting plates on the axle. The measurements suit the parts we supply.

Brake mounting plate location diagram
Brake mounting plate positionsMeasurements are for parts supplied by Trailer Spare Parts Australia.

Shop brakes & hubs

Trailer plug wiring diagrams

All diagrams are viewed from the cable side, which is the back of the plug.

7 pin flat trailer plug wiring diagram
7-pin flatThe standard Australian trailer plug.
12 pin flat trailer plug wiring diagram
12-pin flatFor caravans and campers with extra circuits.
7 pin large round trailer plug wiring diagram
7-pin large round
7 pin small round trailer plug wiring diagram
7-pin small round
Trailer wiring layout diagram
Trailer wiring layoutTypical light circuit layout.

For guidance only. Trailer Spare Parts Australia is not liable for electrical or other faults. If you're unsure, have an auto electrician check your wiring.

Shop lighting & electrical

Building a trailer at home

Yes, you can still build your own trailer. Self-certifying on the identification plate is no longer enough, though. Home-built trailers are now approved through the Australian Government's ROVER system before they can be registered.

  1. Register with ROVERCreate an account on the ROVER website.
  2. Declare complianceSign a declaration that the trailer meets the vehicle standards. Keep your invoices for parts and steel, and photos of each build stage.
  3. Get a VIN, then registerApply for a VIN through ROVER. Once it is issued, register the trailer in your state.

Before you start, read Vehicle Standards Bulletin VSB 1, which covers construction requirements for trailers up to 4.5 tonnes. Also see the government's low ATM trailers page.

Rules and processing times change. Check the current requirements with the Australian Government and your state registration authority before you build.

Need a hand?

Our parts team can match a part from a photo, part number or measurements. Call, email or visit the Archerfield parts counter.

Contact us